西南地区乡镇共墙建造砖混结构房屋典型震害与结构性能改进措施

多年来，西南地区龙门山断裂带发生多次破坏性地震，影响范围较广，导致该地区乡镇居民有大量带震害损伤共墙建造砖混结构房屋留存使用，此类建筑结构使用安全问题需高度关注。通过对该地区乡镇常见共墙建造砖混结构房屋的结构特征及建造技术进行探讨，开展该类型房屋承重墙、预制楼板、楼梯、附属结构典型震害、修复与使用情况调查分析，总结典型共墙建造砖混结构房屋的破坏特点，提出该类型房屋抗震能力评估方法及结构性能改进措施建议。     

行李箱外板浮动整形模设计

介绍了某轿车行李箱外板的翻边侧整形模设计过程,行李箱外板的侧法兰翻边上存在凹包,其翻边方向和凹包成形方向不同,常规需要2道工序分别完成翻边和凹包成形。该模具突破了传统的设计结构,在翻边机构中设置了凹包成形机构,将2个不同方向的成形复合到1道工序中,减少了模具数量,降低了冲压成本和工装成本。     

谷氨酰胺代谢在原发性肝癌发生发展及治疗中的研究进展

肝癌是我国高发并且危害性极大的恶性肿瘤，其具有高死亡率并起病隐匿等特点。目前，肝癌治疗主要是以靶向药物，手术和放化疗为主，容易出现复发率高、耐药性强等现象。本文以谷氨酰胺代谢为切入点，对目前研究较多的肝癌相关的谷氨酰胺代谢酶及相关基因分别予以综述，以期为肝癌的发病机制及药物治疗提供开放性新思路。     

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

The effects of La₂O₃–Al₂O₃–SiO₂ addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La₂O₃–Al₂O₃ and 20 vol% SiO₂ addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La₂O₃–Al₂O₃–SiO₂ system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock.     

低阶煤颗粒-气/油泡间的诱导时间研究

为表征低阶煤颗粒-气/油泡间矿化过程的差异,通过Sutherland理论下固体颗粒进入泡沫产品的总概率(E)和浮选速率常数(k)之间关系,并结合低阶煤颗粒-气/油泡的浮选速率试验,求得了低阶煤颗粒-气/油泡间的诱导时间。浮选实验研究表明,在相同的捕收剂消耗量下低阶煤-油泡浮选产率均高于低阶煤-气泡浮选产率。诱导时间测试表明,低阶煤颗粒-油泡间的诱导时间(35 ms)要明显低于低阶煤颗粒-气泡间的诱导时间(93 ms)。上述实验结果表明,油泡表面的疏水性要强于传统浮选气泡表面的疏水性。然而,进一步利用Sutherland理论中固体颗粒进入泡沫产品的总概率和浮选速率常数之间的数学关系,并结合低阶煤颗粒-气/油泡的浮选速率试验求得的低阶煤颗粒-气/油泡间的诱导时间分别为9.67和8.46 ms,其与诱导时间测试仪分别测量的诱导时间差异很大。这主要是由于在实际浮选过程中气/油泡的上升速度分别为23.26和22.68 cm/s,其远高于2015EZ型诱导时间仪测试过程中气/油泡碰撞速度(2.0 cm/s)。因此,诱导时间理论计算表明气泡-颗粒间的碰撞速度对颗粒-气泡间的诱导时间影响很大。上述研究结果表明油泡浮选效果优于传统浮选的内在原因在于低阶煤颗粒-油泡间的诱导时间小于低阶煤颗粒-气泡间的诱导时间。     

Edge induced band bending in van der Waals heterojunctions: A first principle study

Nano Research - The dangling bond free nature of two-dimensional (2D) material surface/interface makes van der Waals (vdW) heterostructure attractive for novel electronic and optoelectronic...     

应用M-MIVM预测含钛渣系组元活度

 在钢铁冶炼过程中,随着护炉钛材料和含钛铁矿石的应用,大量的含钛炉渣被生产出来。由于缺少多元含钛渣系的热力学数据,限制了钛资源综合利用技术的深入发展。因此,应用改进的分子相互作用体积模型(M-MIVM(FII)),预测了基础渣系Al₂O₃-CaO-SiO₂、FeO-MnO-SiO₂和含钛渣系FeO-MnO-TiO₂、FeO-SiO₂-TiO₂、MnO-SiO₂-TiO₂、Al₂O₃-CaO-FeO-TiO₂中各组元活度,并与试验值比较。结果表明,M-MIVM(FII)的预测值与试验值符合较好,6个体系总的平均相对误差为11%,该精度处于Turkdogan提出的30%以内的试验误差范围; M-MIVM(FII)在参数拟合与活度预测能力方面均优于MIVM,该模型对多元含钛熔渣体系组元活度具有更好的预测效果。在此基础上,应用M-MIVM(FII)预测Al₂O₃-CaO-SiO₂-TiO₂熔体中TiO₂活度,并分析其影响因素。结果表明,TiO₂活度预测值与试验值吻合良好,且随炉渣碱度、Al₂O₃含量的增加而降低,该规律与试验规律相一致。M-MIVM(FII)仅通过拟合子二元系活度或者直接由无限稀活度系数就能够预测多元熔体的热力学性质。     

A novel minimum weight formulation of topology optimization implemented with reanalysis approach

In this paper, we develop an efficient diagonal quadratic optimization formulation for minimum weight design problem subject to multiple constraints. A high-efficiency computational approach of topology optimization is implemented within the framework of approximate reanalysis. The key point of the formulation is the introduction of the reciprocal-type variables. The topology optimization seeking for minimum weight can be transformed as a sequence of quadratic program with separable and strictly positive definite Hessian matrix, thus can be solved by a sequential quadratic programming approach. A modified sensitivity filtering scheme is suggested to remove undesirable checkerboard patterns and mesh dependence. Several typical examples are provided to validate the presented approach. It is observed that the optimized structure can achieve lighter weight than those from the established method by the demonstrative numerical test. Considerable computational savings can be achieved without loss of accuracy of the final design for 3D structure. Moreover, the effects of multiple constraints and upper bound of the allowable compliance upon the optimized designs are investigated by numerical examples.